top of page
RinFire Somatosensory Controller User Manual
Controller Diagram
Buttons
Connecting to Xbox
Connecting to PlayStation
Connecting to Switch
Connecting to PC
Controller Sensitivity
Controller Recoil Switch
Controller Channel Setting
Screen Calibration*
Health and Safety Information and Usage Guidelines
End-User License Agreement
Controller Diagram
Buttons
PlayStation:
Xbox:
Switch:
PC:
PC edition can customize all buttons with RinFire Assistant software.
Each button can be set as a computer keyboard key.
Connecting to Xbox
Xbox 360 / Xbox One / Xbox One S / Xbox One X / Xbox Series S / Xbox Series X :
1. Turn on the console.
2. Connect the Converter to the Control Center and the original Controller as shown in the picture below, then connect the Converter to the Xbox console.
3. After waiting for a few seconds, the indicator light on the converter will flash with a breathing light, which means the connection is successful. At this time, you can use the gaming gun to control the Xbox console.
4. Launch and enter the game.
5. After entering the game, point the USB interface of the controller to the Reticle of the screen, then press and hold the Reticle Calibration button on the controller, at this time Control Center will make a beep sound, wait for the sound to end, release the Reticle Calibration button, and you can use the controller.
Connecting to PlayStation
PlayStation3 / PlayStation4 / PlayStation4 Slim / PlayStation4 Pro :
1. Turn on the console.
2. Connect the Converter to the Control Center and the original Controller as shown in the picture below, then connect the Converter to the PlayStation console.
3. After waiting for a few seconds, the indicator light on the converter will flash with a breathing light, which means the connection is successful. At this time, you can use the gaming gun to control the PlayStation console.
4. Launch and enter the game.
5. After entering the game, point the USB interface of the controller to the Reticle of the screen, then press and hold the Reticle Calibration button on the controller, at this time Control Center will make a beep sound, wait for the sound to end, release the Reticle Calibration button, and you can use the controller.
HEALTH AND SAFETY INFORMATION AND USAGE GUIDELINES
End-User License Agreement
Connecting to Switch
Switch / Switch Lite :
1. Turn on the Switch and Make sure the Pro Controller Wired Communication of Switch is on.
The settings are as follows:
System Settings → Controllers and Sensors → Pro Controller Wired Communication → On
2. Connect the Converter to the Control Center in the picture below, then connect the Converter to the Switch console.
When connecting the Switch Lite, you need to purchase an additional USB to Type-C OTG adapter.
3. After waiting for a few seconds, the indicator light on the converter will flash with a breathing light, which means the connection is successful. At this time, you can use the gaming gun to control the Switch console.
4. Launch and enter the game.
5. After entering the game, point the USB interface of the controller to the Reticle of the screen, then press and hold the Reticle Calibration button on the controller, at this time Control Center will make a beep sound, wait for the sound to end, release the Reticle Calibration button, and you can use the controller.
Connecting to PC
1. Go to www.rinfire.com and download the RinFire Assistant.
2. Install RinFire Assistant on your computer.
3. Plug the Control Center into the USB port of your computer.
4. Run RinFire Assistant and select the game platform. Most games select PC, but some PC games, such as The House of the Dead, select LIGHT GUN 1 .
5. Click on CONTROLLER PROFILE.
6. Set the mapping between the gaming gun buttons and keyboard keys as needed.
7. Once the settings are complete, click SYNC TO CONTROLLER. (Before clicking, make sure the is powered off)
8. Launch and enter the game.
9. After entering the game, point the USB interface of the controller to the Reticle of the screen, then press and hold the Reticle Calibration button on the controller, at this time Control Center will make a beep sound, wait for the sound to end, release the Reticle Calibration button, and you can use the controller.
Controller Sensitivity
There are Three ways to adjust the sensitivity.
Way1:
Adjust the control sensitivity of the game directly. Adjust the vertical or horizontal sensitivity of the controller or mouse from the game settings.
Way2:
① Press and hold the MD button while turning on the power of the gaming gun, at this time the four lights on the game gun are all on.
② Press the M1 button, at this point one of the LEDs on the Control Center flashes (4 LEDs in total). Corresponding to the level of sensitivity (1-4), No. 4 LED means the highest sensitivity, No. 1 means the lowest.
③ Press the M1 button again to change the level of sensitivity, at which time the corresponding LED on the Control Center starts flashing. When the setting is finished, press MD button to store the sensitivity, at this time Control Center makes a beep sound, indicating that the sensitivity setting is finished. After the setting is finished, turn off the power of the gaming gun.
Way3:
① Go to www.rinfire.com and use a Windows PC to download and install the RinFire Assistant.
② Plug the Control Center into the USB port of your computer.
③ Run RinFire Assistant and select the corresponding gaming platform, then click GAMING GUN PROFILE.
④ Click OTHER PROFILES, then adjust the GAMING GUN SENSITIVITY, and then click SYNC TO GAMING GUN after the adjustment is finished.
Controller Recoil Switch
1. Press and hold the MD button while turning on the power of the gaming gun, at this time the four lights on the game gun are all on.
2. Press the M2 button.
If the recoil function is currently on, the game gun will vibrate once. Pressing the M2 button once more at this point will turn off the recoil function. When the recoil function is turned off, the 4 Led lights will flash a few times.
Press the MD button to exit the setting.
Controller Channel Setting
When multiple gaming guns are used in a space, the channel of the gaming guns needs to be set to prevent mutual interference. There are 15 channels in total.
1.Make sure the Control Center is not plugged into the USB port(Control Center is not powered).
2. Press and hold the MD button while turning on the power of the gaming gun, at this time the four lights on the gaming gun are all on.
3. Press the M4 button.
At this time the indicator light on the gaming gun will start flashing, the number of flashes is the current channel number (flashing 1 times and then pause to indicate channel 1, flashing 15 times and then pause to indicate channel 15).
4. Press the M5 button to increase the channel number, and press the M6 button to decrease the channel number.
5. After selecting the channel number, insert the Control Center into the USB port (Control Center is powered), Control Center will emit 3 beeps continuously, indicating that Control Center has installed the channel number you selected.
6. Press the MD button on the gaming gun to store the channel number (1 and 2 indicator lights on once), and the gaming gun automatically exits the setting.
Screen Calibration*
Most games do not require screen calibration, only Light Gun mode will be more accurate if the screen is calibrated.
Step1: Plug the Control Center into the USB port(PC or Conventer).
Step2: Power on the gaming gun. Point the muzzle of the gaming gun to the center of the screen, then press and hold the MARK button on the gaming gun, at this time Control Center will make a beep sound, wait for the sound to end, release the MARK button.
Step3: Press and hold SC button for 3 seconds to activate Screen Calibration.
Step4: In the position of the gaming, aim at the left border of the screen and shoot the first shot.
(Do not use gun sight to aim, use the gaming posture to aim)
Step5: In the same way, aim at the right border of the screen and shoot the second shot.
One long beeping sound, indicates calibration successful.
Caution: The calibration order of the border cannot be reversed!
If the calibration fails, you need to restart the gaming gun, and do it again.
Restore Screen Calibration default data:
If you no longer play Light Gun mode, you can restore the default data.
Step1: Plug the Control Center into the USB port(PC or Conventer).
Step2: Power on the gaming gun. Point the muzzle of the gaming gun to the center of the screen, then press and hold the MARK button on the gaming gun, at this time Control Center will make a beep sound, wait for the sound to end, release the MARK button.
Step3: Press and hold SC button for 3 seconds to activate Screen Calibration.
Step4: To any position (the same position) continuous shooting 2 times, you can restore the default data.
Other Support Options
bottom of page